🖤 BF20 FOR 20% OFF, NO MINIMUM SPEND · BF30 FOR 30% OFF, MIN $200 SPEND 🖤

BYD Atto 1 Wiper Blade Sizes

This guide is for everyday BYD Atto 1 owners who want to replace their windscreen wiper blades but are not sure where to start. It sets out the driver side and passenger side blade sizes for the Atto 1, so you can pick the right blades with confidence. You do not need any technical knowledge to follow it. Just read the section that matches your car and take the sizes to the shop or order them online.

Wiper blade sizes can differ between generations of the same model, so it pays to check which generation you have before buying. This guide covers the Atto 1 generation listed below and gives the driver side and passenger side sizes for it. Matching each side correctly matters, because a blade that is too long or too short will not clear your windscreen properly.

To use the guide, first work out which generation your Atto 1 belongs to, then note the driver side and passenger side sizes. Check the wiper arm type shown for your generation so you know how the blade releases. Fit one side at a time and test the wipers before you finish. If anything looks unclear, check your car's details again before ordering.

BYD Atto 1 wiper sizes for each generation

BYD Atto 1 2024-2027

BYD Atto 1 2024-2027 wiper blades
Driver side24″600 mm
Passenger side16″400 mm

Push-button arm. Your wiper arm uses a push-button-type connector, and the blade supplied is made for it.

Shop 2024-2027 wiper blades

For the 2024 to 2027 BYD Atto 1, the driver side blade is 24 inch (600 mm) and the passenger side blade is 16 inch (400 mm). Buy one blade of each size and keep them matched to their sides when fitting. Before you start, lift the wiper arm away from the glass so you have room to work, and lay a cloth over the glass in case a blade slips. Take a moment to compare the new blade with the old one before you click it into place.

How to work out which BYD Atto 1 you have

Start by confirming which generation your Atto 1 is. The generation is shown by the years it was built, so check your car's build details or paperwork and match them to the years in this guide. Once you are sure, note the driver side and passenger side sizes for that generation. Do not assume the sizes are the same on both sides, because they are not.

When you have the sizes, buy one blade for the driver side and one for the passenger side. Keep each blade with its own side as you unpack it, so you do not mix them up. Fit the driver side first, then the passenger side, and check that each blade sits flat against the glass. A quick test run will show you whether both sides clear the screen evenly.

How to fit your new wiper blades

Push-button arm

The blade has a small push button that releases it from the end of your wiper arm.

  1. Lift the wiper arm away from the windscreen until it stays upright.
  2. Press and hold the push button on the blade connector, then slide the blade off the end of the arm.
  3. Slide the new blade on until the button clicks back into place.
  4. Gently lower the arm back onto the glass.

When to replace your wiper blades

Worn wiper blades show themselves in everyday driving. You may see streaks of water left behind after each sweep, or smears that make the glass harder to see through. Some blades squeak or judder across the screen, and others leave patches that never clear. If you notice any of these signs, it is time to think about new blades.

Look closely at the rubber edge of each blade. Split, cracked or hardened rubber cannot wipe the glass cleanly, even if the arm still moves. A blade that has lost its flexibility will skip and chatter, and it may scratch the glass over time. Replacing worn blades is a simple job that makes a real difference to how well you can see.

Clear visibility matters for safe driving, especially in rain or spray from other vehicles. Blades that streak or smear can hide hazards and make judging distance harder. Do not wait for a completely failed blade before you act. If your wipers are not clearing the screen properly, fit new ones and enjoy a clearer view.

Looking after your wipers

Look after your wipers and they will look after you. Clean the windscreen regularly, because dirt and film on the glass wear the rubber edge faster. Wipe the blade edge with a damp cloth now and then to remove grit and dust. Sun and dust both dry out and wear rubber, so park in shade where you can and keep the glass clean.

When you wash the car, lift the wiper arms off the glass gently so you can clean underneath them. Do not let an arm snap back down onto the glass, as this can damage the blade or the screen. Check your washer fluid regularly and top it up, because a good spray helps the blades clear the screen. These small habits keep your wipers working well for longer.

Wiper blade tips

  • Check which generation your Atto 1 is before you buy any blades.
  • Match each blade to its side: driver side and passenger side sizes are different.
  • Lift the wiper arm gently and lay a cloth on the glass while you work.
  • Wipe the blade edge with a damp cloth to remove grit and dust.
  • Top up your washer fluid so the blades can clear the screen properly.
  • Replace blades at the first sign of streaking, smearing or squeaking.

Frequently asked questions

What size wiper blades does the BYD Atto 1 need?

For the 2024 to 2027 generation, the driver side blade is 24 inch (600 mm) and the passenger side blade is 16 inch (400 mm). Buy one of each size and keep them matched to their sides when fitting.

How do I know which generation my Atto 1 is?

Check the years your car was built and compare them with the years shown in this guide. The generation listed here covers 2024 to 2027. If your car falls in that range, use the sizes given for it.

Can I use the same size blade on both sides?

No. The driver side and passenger side sizes are different for the Atto 1. The driver side takes 24 inch (600 mm) and the passenger side takes 16 inch (400 mm). Fit each blade to its correct side so both clear the glass properly.

How does the blade come off the wiper arm?

The Atto 1 uses a push-button arm. The blade has a small push button that releases it from the end of your wiper arm. Press the button and ease the blade away, then click the new one into place.

How often should I replace my wiper blades?

There is no fixed number in this guide. Watch for the signs instead: streaking, smearing, squeaking, judder, or split and cracked rubber. When your blades stop clearing the screen cleanly, fit new ones.

Why do my new blades still streak?

Streaking can come from dirt or film on the glass, so give the windscreen a good clean. Check that each blade is seated properly on the arm and matched to the correct side. If the problem continues, look at the blade edge for damage.

More BYD wiper blade sizes

If you can't find your car in the list, please scroll down to ensure you haven't missed it. If you're not 100% sure, select the option you think is closest. A photo of the car will be shown to help you confirm if it's the correct model. If you still can't find your car, please fill out the form below with your vehicle details and we'll respond shortly.

Enter valid email address!

Your name, Email Address and Correct Answer of QUIZ is required field!

Please do not use HTML tags.

Thank you for your inquiry. We will check and get back to you shortly.