🖤 BF20 FOR 20% OFF, NO MINIMUM SPEND · BF30 FOR 30% OFF, MIN $200 SPEND 🖤

Audi Q3 Wiper Blade Sizes

This guide is for everyday Audi Q3 owners who want to replace their windscreen wiper blades without any fuss. It covers the two Q3 generations and gives you the driver side, passenger side and rear sizes for each one, so you can pick the right blades the first time. You do not need any technical knowledge to use it. Just read through, find your generation, and match the sizes to your car.

The Q3 has been built in two generations, and the wiper sizes differ between them. That means a blade that fits one generation may not fit the other. It is worth taking a moment to confirm which generation you have before you buy anything. The guide lists the generations in order, with the years for each, so you can work out where your car fits.

Use the guide by finding the generation that matches your Q3, then noting the driver side, passenger side and rear sizes. Each generation also shows the wiper arm type, so you know how the blade attaches. Check your car against the details before ordering. If anything looks different on your vehicle, stop and check again. A few minutes now saves a return trip later.

Audi Q3 wiper sizes for each generation

Audi Q3 2019-2026 (F3)

Audi Q3 2019-2026 (F3) wiper blades
Driver side24″600 mm
Passenger side20″500 mm
Rear16″400 mm

Push-button arm. The blade has a small push button that releases it from the end of your wiper arm.

Shop 2019-2026 (F3) wiper blades

For the 2019-2026 (F3) Q3, the driver side blade is 24 inch (600 mm) and the passenger side blade is 20 inch (500 mm). The rear blade is 16 inch (400 mm). These are the sizes to look for when you shop. Before fitting, compare the new blade with the old one side by side to be sure they match. Take your time and fit one side at a time so you do not mix them up.

Audi Q3 2012-2018 (8U)

Audi Q3 2012-2018 (8U) wiper blades
Driver side24″600 mm
Passenger side21″525 mm
Rear16″400 mm

Push-button arm. The blade has a small push button that releases it from the end of your wiper arm.

Shop 2012-2018 (8U) wiper blades

For the 2012-2018 (8U) Q3, the driver side blade is 24 inch (600 mm) and the passenger side blade is 21 inch (525 mm). The rear blade is 16 inch (400 mm). Keep these figures handy when you order. When you fit the new blades, make sure each one clicks securely into place on its arm before you lower it. A quick tug after fitting tells you it is seated properly.

How to work out which Audi Q3 you have

To work out which generation you have, start with the year your Q3 was built. The generations are listed with their year ranges, so match your car to the right one. If your car sits near a changeover year, check the details on the car itself rather than guessing. You can also look at the shape of the wiper arm and how the blade attaches, and compare that with the arm type shown for each generation.

Once you know your generation, match each side separately. The driver side and passenger side can be different sizes, so do not assume one blade fits both. Note the driver side size, then the passenger side size, then the rear size if your generation lists one. Buy blades that match each position exactly. Fitting the wrong size to a side can leave patches of glass you cannot see through.

How to fit your new wiper blades

Push-button arm

The blade has a small push button that releases it from the end of your wiper arm.

  1. Lift the wiper arm away from the windscreen until it stays upright.
  2. Press and hold the push button on the blade connector, then slide the blade off the end of the arm.
  3. Slide the new blade on until the button clicks back into place.
  4. Gently lower the arm back onto the glass.

When to replace your wiper blades

Worn wiper blades show themselves in small ways at first. You may see streaks of water left behind after each sweep, or a smear that makes the glass harder to see through. Sometimes the blades squeak or judder across the windscreen. These are all signs that the rubber is no longer doing its job properly.

Look closely at the blade edges too. Split or cracked rubber, or chunks missing from the edge, mean it is time for new blades. A blade that leaves the glass cloudy in rain is a safety problem, not just an annoyance. Poor visibility in wet weather makes it harder to see other cars, pedestrians and road markings.

Replacing worn blades is one of the simplest things you can do for safe driving. Do not wait for a storm to notice the problem. If your blades streak, smear, squeak or look damaged, fit new ones. Clear glass in the rain gives you more time to react, and that matters every time you drive.

Looking after your wipers

Look after your wipers and they will look after you. Clean the glass regularly, because dirt and film on the windscreen wear the rubber down faster. Wipe the blade edges with a damp cloth now and then to remove grit. Sun and dust are hard on rubber, so park in the shade when you can. Lifting the arms off the glass when you wash the car helps you clean underneath them.

Check your washer fluid often and top it up when it runs low. Good fluid helps the blades sweep cleanly and clears the glass between wipes. When you lift the arms, do it gently and do not let them snap back onto the glass. Handle the blades by the frame, not the rubber edge, and they will last longer.

Wiper blade tips

  • Check your generation before you order any blades.
  • Match the driver side and passenger side sizes separately.
  • Compare the new blade with the old one before fitting.
  • Fit one side at a time so you do not mix them up.
  • Wipe the glass and blade edges clean now and then.
  • Replace blades at the first sign of streaking or squeaking.

Frequently asked questions

How do I know which Q3 generation I have?

Check the year your Q3 was built and compare it with the year ranges in this guide. If your car is near a changeover year, look at how the blade attaches to the arm and compare it with the arm type shown for each generation.

Are the driver and passenger blades the same size?

No. The driver side and passenger side sizes can differ, so check each one separately in the guide. Buy a blade that matches each position exactly rather than assuming one size fits both sides of the car.

Does my Q3 have a rear wiper?

Both generations listed in this guide show a rear blade size, so check the rear size for your generation. If your car does not appear to have a rear wiper, look again at the vehicle before ordering any rear blade.

How do I fit the new blade to the arm?

The arm type shown for your generation tells you how the blade releases. Follow that method, then push the new blade on until it clicks into place. Give it a gentle tug to confirm it is secure before you lower the arm.

How often should I replace my wiper blades?

Replace them when you notice the signs: streaking, smearing, squeaking, juddering, or split and cracked rubber. Do not wait for heavy rain to find out they are worn. New blades give you clearer glass and safer driving.

What causes wipers to squeak?

Squeaking often comes from worn or hardened rubber, or from dirt and film on the glass. Clean the glass and the blade edges first. If the noise continues, the blades are likely worn and ready to be replaced with new ones.

More Audi wiper blade sizes

If you can't find your car in the list, please scroll down to ensure you haven't missed it. If you're not 100% sure, select the option you think is closest. A photo of the car will be shown to help you confirm if it's the correct model. If you still can't find your car, please fill out the form below with your vehicle details and we'll respond shortly.

Enter valid email address!

Your name, Email Address and Correct Answer of QUIZ is required field!

Please do not use HTML tags.

Thank you for your inquiry. We will check and get back to you shortly.